2019 Winter Custom Carolina 42 WALK AROUND EXPRESS

ENGINE CHOICES INCLUDE BUT NOT LIMITED TO:

CAT C7.1-  500 HP

CAT C8.7- 640 HP

CUMMINS QSC 8.3- 600 HP

OPTIONS INCLUDE BUT NOT LIMITED TO:

SEAKEEPER 6

BOW THRUSTER W/ CONTROLS INTEGRATED TO THROTTLE HANDLES

LIVOS MOISTURE ELIMINATORS

HVAC (CABIN)

HVAC (BRIDGE)

BRIDGE REFRIGERATION (4 BOXES)

REMOVABLE PULPIT W/ SS GROUND TACKLE

LEWMAR V3 WINDLASS

MACERATED INDECK FISH BOX (1)

FAUX TEAK TOE RAIL

FAUX TEAK TRANSOM

FAUX TEAK BRIDGE FURNITURE

FAUX TEAK DODGER CAP

CUSTOM PAINTED TRANSOM GRAPHIC

TEAK DECK COCKPIT

TEAK DECK BRIDGE

TEAK COVERING BOARDS

TEAK HELM POD

TEAK CABIN DOOR

TRANSOM DOOR : STANDARD

ELECTRIC REEL OUTLETS UNDER COVERING BOARDS

ROD HOLDERS (10)

UNDERWATER LIGHTS (2)

ROD STORAGE: STANDARD

OUTRIGGER HARDWARE

TRANSOM FISHBOX PLUMBED FOR LIVEWELL: STANDARD

SUBZERO REFRIG/FREEZER DRAWER UNIT

GALLEY COOKTOP

MICROWAVE

STAINLESS SCUPPER PLATES

COVERIND BOARD HAWSE PIPES

FULL TOWER/ RUPP MANUAL RIGGERS

RELEASE CHAIR PACKAGE (2 HELM+COCKPIT)

WHISPERWALL INTERIOR+HEADLINER

ENCLOSURE 3 SIDED

SOUNDOWN ENGINE ROOM INSULATION

•   Anchor locker painted and faired with secure latch

•   Fresh water wash down spigot in Anchor locker

•   Chafe gear and rope chocks at cleats on toe rail

•   10” cleats on bow

•   10” spring cleats

•   Under deck lighting all the way around boat

•   Non-skid foredeck and walk around sole

•   Queen size bunk with vinyl cushion top

•   Side night stand to each side with solid surface counter

•   Full height compartment to starboard with shelves for storage

•   Overhead cabinets with counters below to port

•   Solid surface countertops throughout

•   Custom Teak and Maple cabin sole

•   Teak steps

•   Recessed LED Lights in overhead

•   Padded wall panels where capable

•   Teak Cabinetry throughout interior

•   16,000 BTU Marine Air Conditioner

•   Jenn-Air refrigerator/freezer drawers

•   Microwave in upper galley cabinet

1.  Freshwater flush head with holding tank

2.  Recessed LED lights in headliner/ soffit  White Painted surfaces

    Shower inside of head compartment

•   Polished Pipe (2) Antenna Standoffs

•   Recessed Lights, Lumitec tri color

•   Radar pod express style

•   Molded 2 in 1 LED spreader light Lumitec light pod over cockpit

•   Rod holder polished welded to rail behind hardtop

•   Rod holder polished welded to aft legs

•   Rupp outriggers 32’ double spreader solid back bar

•   Install Rupp outriggers mounted on hardtop

•   Rupp center rigger

•   Nav lights port, starboard, stern molded into hardtop

•   2- Cummins QSC 600 HP

•   2-Cummins Mercruiser Engine display 7”

•   1- Onan 7kW generator with sound shield

•   Seakeeper 5 Gyro

•   Side mounted “Palm Beach” control handles and controls with bow thruster push buttons

•   Custom Painted white engines

•   Veem Propellers

•   Custom Stainless rudders

•   12v engine wiring system

•   Aluminum stringer caps

•   230V Headhunter Stingray pump (fresh)

•   Jabsco 12v water pump (salt)

•   110V and 12V engine room lighting

•   1- Sentry battery charger 20 amp 12V

•   Racor fuel filters for each engine and generator

•   6-Optima Marine Batteries

•   Sea strainer on genset

•   Tank sender on tank

•   Fireboy halon fire control system

•   Seacocks on all thru hulls

•   Stainless thru hull fittings above water line

•   Lenco Hatch lift actuators for salon deck lift

•   Instant hot water heater

•   50 gallon fresh water tank

•   Rule Bilge pumps in engine room, lazarette, and forward bilge with high water alarms

•   475 gal fuel capacity in cockpit

•   15 gal holding tank with macerator pump and pump out access

•   5 gal Vetus grey water sump

•   All wiring guided by ABYC standards

•   50 amp 240V service

•   Iso-Boost for surge protection

•   1- 50 amp outlet in cockpit

•   Custom Paneltronics panels AC/DC

•   Appropriate wiring to supply systems

•   12V wiring to all DC systems including navigational lights

•   Lenco trim tabs

•   Helm forward and starboard adjusted on bulkhead

•   Dash space for electronics equipment (Dual 19” screens)

•   Offset cabin access with sliding access door (Sliding door Teak)

•   2- Release Marine” Contour Series” Teak ladder Back chair at helm (not in base boat price)

•   Teak helm pod (Custom panel underneath for startup switches and trim tabs)

•   Mirrored combination mezzanine and deck seating.

•   Cushions per owner specifications

•   All boxes insulated to maintain ice

•   Main deck lifts to reveal engine space and access to mechanical components

•   Forward facing seating to hinge with deck hatch

•   Mezzanine seating facing aft

  •   Insulated ice storage boxes

  •   Tackle drawers in mezzanine seating

•   Port shore power hook-up connections

•   Large insulated transom bait well/fish box with vacuum overflow

•   Covering board hawse pipes

•   Under gunnel courtesy lighting

•   6 Pompanette rod holders

•   Teak Deck in cockpit and bridge deck

•   Nonskid walk around deck

•   Teak Covering Boards with full teak coaming face

•   Teak Release Marine 6- rod holder battle saddle (not in base boat price)

•   Fresh water wash down spigot

•   Salt water wash down spigot

•   Electric reel outlets under gunnels

Bottom

•   2-Layers 1⁄2” marine grade Douglas fir

•   2- Layers 1808 Vectorply biaxial fiberglass sandwiched between each layer

•   1-layer 3408 Vectorply biaxial fiberglass outside bottom impregnated with West System Epoxy

•   2-layer 3408 Vectorply biaxial fiberglass on keel and chine

•   1-layer 1808 Vectorply biaxial fiberglass inside bottom up through hull side

•   Laminated Douglas Fir/ 3⁄4” Okume plywood stringers

•   Vectorply propeller tunnels integrated to provide 36” draft

  Hull Sides

•   Hull side 2 layers 6mm Okume plywood Loyds type 1088

•   2- layers 1208 Vectorply biaxial fiberglass laminated between each layer

•   1-layer 3408 Vectorply biaxial fiberglass impregnated with West System Epoxy

•   Laminated Douglas Fir rib bands

•   Laminated Douglas Fir chine

•   Laminated Cypress sheer clamp

  Bilge

 All bilges, engine room, and pump room faired and painted with Awlcraft 2000 Express construction

•   1- layer 1” Diab A500 Foam on cabin

•   2-layer 1808 Vectorply biaxial fiberglass impregnated with West System Epoxy

  All exterior surfaces

•   A build up of Alexseal fairing products followed by 9 coats of Alexseal primer to a finished surface

•   - Topsides: Cloud white Alexseal

•   - Hull: Cloud white Alexseal

  Exterior Finishes

 1” solid Stainless steel bumper metal